• product up1

Products

Hot-selling Upvc Pipes Mould - CPVC Elbow Pipe Fitting Mould – Longxin

Short Description:


Product Detail

Product Tags

Related Video

Feedback (2)

Sticking to the principle of "Super High-quality, Satisfactory service" ,We are striving to generally be a very good business partner of you for Pp-R Fitting Mould Elbow 90°, Upvc Elbow Mould, 90 Degree Elbow Pipe Fitting Mould, We sincerely hope to serve you and your business with a good start. If there is anything we can do for You, we shall be more than pleased to do so. Welcome to our factory for visit.
Hot-selling Upvc Pipes Mould - CPVC Elbow Pipe Fitting Mould – Longxin Detail:

Introduce

The product introduction of our CPVC elbow mold is as follows :

[Mold material] 45# quenched and tempered, 60# quenched and tempered, P20, P20H, 718, 718H, 2738, 7138, NAK80, S136, SKD61, etc. according to customer needs.

[Mold design software] Moldflow, UG, PROE, AUTOCAD, Cimatron E, etc.

[Mold cooling system] Optimized design of circulating water to improve production efficiency and reduce your costs.

[Mold mid-term treatment] quenching and tempering to improve hardness.

[Mold post-treatment] (The nitriding treatment temperature is low, the deformation is small, and no quenching is required, it has high surface hardness (greater than HV8500) and wear resistance.

Details

[Mold life]  Normal use is not less than 500,000 times.

[Transportation method]  Before the mold is shipped, the clamping piece must be installed, wrapped with stretch film, and then packed in a wooden box. The packaging is sturdy and rust-proof, avoiding damage to the mold during transportation, and finally logistics transportation to the customer

[Place of Origin]  Huangyan, Taizhou, Zhejiang.

901

FAQ:

1. Pipe fitting mould What should I do if the ejector pin is bent or broken during normal production?

Now we are targeting this CPVC elbow pipe fitting mold

Make a detailed introduction:

The self-made ejector rods are of better quality, but the processing cost is relatively high. Nowadays, the mold structure generally uses standard parts, and the quality is at the conventional level. If the gap between the ejector pin and the guide hole is too large, material leakage will occur; but if the gap is too small, the mold temperature will increase during injection molding, which will cause the ejector pin to expand and become stuck, sometimes even after the ejector pin is ejected for a certain distance It will not move and deform, resulting in the next mold closing, the higher ejector rod cannot be reset and directly hit the cavity.

If CPVC Elbow Pipe Fitting Mould is generated normally

When this problem occurs, the ejector pin should be re-ground. The mold structure retains a 10-15 mm mating section at the front end of the ejector pin, and the middle part is ground 0.2 mm smaller. After all ejector rods are assembled, their fit clearance must be strictly checked, generally within 0.05-0.08 mm, to ensure that the entire ejector mechanism can advance and retreat freely.

2. What should I do if CPVC Elbow Pipe Fitting Mould has poor cooling or water leakage during the production process?

The cooling effect of CPVC Elbow Pipe Fitting Mould directly affects the product quality and production efficiency. Such as poor cooling, large shrinkage of the product, or uneven shrinkage, resulting in warping deformation and other defects; on the other hand, the Fitting Mould is overheated in whole or part, so that the mold cannot be formed normally and production is stopped. In severe cases, the movable parts such as ejector rods may be thermally expanded. Dead and damaged.

The design and processing of the cooling system depends on the shape of the product. Don’t omit this system because of the complicated structure of the pipe fitting mold or the difficulty in processing, especially for large and medium-sized molds. The cooling problem must be fully considered.

egr

The Exhibition

微信图片_20200929110140
微信图片_20200929110131


Product detail pictures:

Hot-selling Upvc Pipes Mould - CPVC Elbow Pipe Fitting Mould –  Longxin detail pictures

Hot-selling Upvc Pipes Mould - CPVC Elbow Pipe Fitting Mould –  Longxin detail pictures

Hot-selling Upvc Pipes Mould - CPVC Elbow Pipe Fitting Mould –  Longxin detail pictures


Related Product Guide:

To get the stage of realizing dreams of our employees! To build a happier, more united and much more skilled crew! To reach a mutual benefit of our prospects, suppliers, the society and ourselves for Hot-selling Upvc Pipes Mould - CPVC Elbow Pipe Fitting Mould – Longxin , The product will supply to all over the world, such as: Saudi Arabia, Rotterdam, Salt Lake City, For more than ten years experience in this filed, our company has gained high reputation from home and abroad. So we welcome friends from all over the world to come and contact us, not only for business, but also for friendship.
  • The goods we received and the sample sales staff display to us have the same quality, it is really a creditable manufacturer.
    5 Stars By Edward from Vietnam - 2018.12.10 19:03
    It is not easy to find such a professional and responsible provider in today's time. Hope that we can maintain long-term cooperation.
    5 Stars By Novia from Rotterdam - 2018.11.04 10:32
    Write your message here and send it to us